[APP] Visonic PowerMax App (1.1.1). I understood the setup for the Homey and Visonic PowerMax Pro integration using the Visonic (dual) RS-232 Interface Module in.

• POWERMAX PRO Installer Guide Fully Supervised Wireless Alarm Control System TABLE OF CONTENTS 1. INTRODUCTION.3 4.4.21 “Not Active”.16 4.4.22 Back Light.16 2. 3 4.4.23 Duress.16 2.1 General Data.3 4.4.24 Piezo Siren.16 2.2 RF Section.4 4.4.25 Reset Option. • SIA Event Codes.35 D10. Perimeter Zones.

37 4/2 Event Codes.35 D11. Perimeter Follower Zones.37 Understanding the Scancom Reporting Protocol Data D12. Temperature Zone.37 Format.36 D13. 24-Hour Zones.37 APPENDIX D. Programmable Zone Types.36 D14.

INTRODUCTION • The PowerMax Pro is a user and installer-friendly, 30-zone Special wall-mounted bracket permits installation without fully-supervised wireless control system. The system is having to open the unit’s plastic casing. Designed to function in a way that appeals to the user but •. • 2.2 RF Section The backup periods, when the PowerMax Pro includes internal PowerLink with 1 active camera, GSM and Operating Frequencies (MHz): 315, 433 or 868.95 proximity reader, with external load connected between Receiver Type: Super-heterodyne, fixed frequency +12 / V+ terminal and GND terminal, is as follows: Receiver Range: 600 ft (180 m) in open space Battery Pack Battery pack.

• Separate the back unit from the front unit Back unit Position the back unit on the desired mounting location and mark 4 drilling points Release on mounting surface screws Back unit Drill 4 holes and insert wall anchors Fasten the back unit with 4 screws Figure 3.1a –. • PHONE WIRING USING TERMINAL BLOCK CONNECTORS (NORTH AMERICA) 8-POSITION RJ-31X JACK RJ-31X PLUG GRAY BROWN LINE HOUSE FROM RJ-31X PHONES GREEN STREET GRAY RJ-31X BROWN CORD Figure 3.1b – Phone Wiring Phone wiring in the UK: Line terminals must be connected to pins 2 and 5 of the wall jack. For all installations: If DSL service is present on the phone line, you must route the phone line through a DSL filter (refer to MESSAGE TO THE INSTALLER on page 2 for further details). • Figure 3.1f. -or- Through direct connection of the 12.5 VDC power supply to the expander card via the wall mounted switched AC/DC power supply (supplied by Visonic), as shown in Figure 3.1g. Extract either of these cable clamps. • POWER CONNECTION FOR USA ONLY 100-240V 50/60Hz 12.5VDC Wall Mounted Switched AC/DC Power Supply Figure 3.1g – Wall Mounted Switched AC/DC Power Supply Connection 3.6.3 Optional GSM/GPRS Module 3.6 Front Unit Preparation Mounting 3.6.1 Backup Battery Insertion Caution!

Do not insert or remove the GSM module when Open battery compartment cover (see Figure 3.1h). • 3.7 Final Closure Connect the flat cables in their respective connectors (2 - 5, according to options).

Haste, Dispel magic, Flaming arrow 4. Fire shield Blue, Fire shield Blue, Greater Malison, Stoneskin 5. Magic missile, Summon familiar 2. Invisibility, Mirror image, Knock 3. Baal.

Front unit Back unit Close the panel and fasten the 2 screws. Figure 3.1k - Final Closure D-302541. PROGRAMMING 4.1.3 Installer’s Menu 4.1 INTRODUCTION The installer's menu is shown in Figure 4.1a. The text in Your system is equipped with a partitioning feature (in a rectangles represents the current PowerMax Pro display. PowerMax Pro Partition system) that can divide your alarm 4.1.4 Setting a New Installer Code system into three distinct areas identified as Partition 1 through 3.

4.1a) By using By using INSTALLER CODE MASTER INSTALLER CODE 1. NEW INSTL CODE (see fig. 4.1a) (see fig.

NEW INSTL CODE 1. NEW INSTL CODE NEW INST.

CODE NEW MASTER CODE NEW INST. CODE NEW INST. • ENROLLING TYPE ENROLL SENSORS ENROLL KEYFOB SET SENSITIV. Normal enroll Keyfob No: - by tamper higher sensitiv [Keyfob No.] (****) (e.g. 5) (**) lower sensitiv Select by Keyfob No: 5 Keyfob No: 5 TRANSMIT NOW TO DELETE ZONE No: - - (press (First display) [wired Zone No. • 4.3 DEFINING ZONE TYPES, NAMES, CHIME ZONES & PARTITION This mode allows you to assign one of 15 zone types to A list of factory defaults is printed in table 1. You may fill each of the system's 30 (wireless & wired) zones.

You can out the blank columns even before you start and proceed define zones as KEY ZONES, to enable arming/disarming to program according to your own list. • Table 1 - DEFAULT AND PROGRAMMED ZONE DEFINITIONS Zone Zone Type Zone Name Chime (melody Partition Default Programmed Default Programmed Zone Name or Off) (*) Delay 1 Front Door Delay 1 Garage Delay 2 Garage Door Perimeter Back Door Perimeter Child Room Interior Office. • 4.4.6 Alarm Cancel 4.4.12 Panic Alarm (Fig. 4.4, location 06). Here you determine the ”cancel (Fig. 4.4, location 12). Here you determine whether the alarm” period that starts upon reporting an alarm to the user will be allowed to initiate a panic alarm by central station.